power.h

Go to the documentation of this file.

/* SPDX-License-Identifier: GPL-2.0-only */
 
/* Register map for Exynos5 PMU */
 
#ifndef CPU_SAMSUNG_EXYNOS5250_POWER_H
#define CPU_SAMSUNG_EXYNOS5250_POWER_H
 
#include <soc/cpu.h>
 
/* Enable HW thermal trip with PS_HOLD_CONTROL register ENABLE_HW_TRIP bit */
void power_enable_hw_thermal_trip(void);
 
#define MIPI_PHY1_CONTROL_ENABLE                (1 << 0)
#define MIPI_PHY1_CONTROL_M_RESETN              (1 << 2)
 
#define POWER_USB_PHY_CTRL_EN                   (1 << 0)
#define POWER_PS_HOLD_CONTROL_DATA_HIGH         (1 << 8)
#define POWER_ENABLE_HW_TRIP                    (1UL << 31)
 
#define EXYNOS_DP_PHY_ENABLE    (1 << 0)
 
/* PMU_DEBUG bits [12:8] = 0x1000 selects XXTI clock source */
#define PMU_DEBUG_XXTI                          0x1000
/* Mask bit[12:8] for xxti clock selection */
#define PMU_DEBUG_CLKOUT_SEL_MASK               0x1f00
 
/* Power Management Unit register map */
struct exynos5_power {
        /* Add registers as and when required */
        uint32_t        om_stat;                /* 0x0000 */
        uint8_t         reserved1[0x03fc];
        uint32_t        sw_reset;               /* 0x0400 */
        uint8_t         reserved2[0x0300];
        uint32_t        usb_drd_phy_ctrl;       /* 0x0704 */
        uint32_t        usb_host_phy_ctrl;      /* 0x0708 */
        uint8_t         reserved3[0x8];
        uint32_t        mipi_phy1_control;      /* 0x0714 */
        uint8_t         reserved4[0x8];
        uint32_t        dptx_phy_control;       /* 0x0720 */
        uint8_t         reserved5[0xdc];
        uint32_t        inform0;                /* 0x0800 */
        uint32_t        inform1;                /* 0x0804 */
        uint8_t         reserved6[0x1f8];
        uint32_t        pmu_debug;              /* 0x0a00 */
        uint8_t         reserved7[0x2724];
        uint32_t        padret_uart_opt;        /* 0x3128 */
        uint8_t         reserved8[0x1e0];
        uint32_t        ps_hold_ctrl;           /* 0x330c */
} __packed;
check_member(exynos5_power, ps_hold_ctrl, 0x330c);
 
static struct exynos5_power *const exynos_power = (void *)EXYNOS5_POWER_BASE;
 
/**
 * Perform a software reset.
 */
void power_reset(void);
 
/**
 * Power off the system; it should never return.
 */
void power_shutdown(void);
 
/* Enable DPTX PHY */
void power_enable_dp_phy(void);
 
/* Initialize the pmic voltages to power up the system */
int power_init(void);
 
/* Read the reset status. */
uint32_t power_read_reset_status(void);
 
/* Read the resume function and call it. */
void power_exit_wakeup(void);
 
/* pmu debug is used for xclkout, enable xclkout with source as XXTI */
void power_enable_xclkout(void);
 
/* Release UART retention on resume (only for debugging, may conflict with
 * kernel). */
void power_release_uart_retention(void);
 
#endif