gpio.c

Go to the documentation of this file.

/* SPDX-License-Identifier: GPL-2.0-or-later */
 
#include <baseboard/gpio.h>
#include <baseboard/variants.h>
#include <commonlib/helpers.h>
#include <soc/gpio.h>
 
/* Pad configuration in ramstage */
static const struct pad_config override_gpio_table[] = {
        /* A7  : SRCCLK_OE7# ==> NC */
        PAD_NC(GPP_A7, NONE),
        /* A17 : DISP_MISCC ==> NC */
        PAD_NC(GPP_A17, NONE),
        /* A19 : DDSP_HPD1 ==> NC */
        PAD_NC(GPP_A19, NONE),
        /* A20 : DDSP_HPD2 ==> NC */
        PAD_NC(GPP_A20, NONE),
        /* A21 : DDPC_CTRCLK ==> NC */
        PAD_NC(GPP_A21, NONE),
        /* A22 : DDPC_CTRLDATA ==> NC */
        PAD_NC(GPP_A22, NONE),
 
        /* B3  : PROC_GP2 ==> eMMC_PERST_L */
        PAD_CFG_GPO_LOCK(GPP_B3, 1, LOCK_CONFIG),
        /* B5  : ISH_I2C0_SDA ==> NC */
        PAD_NC_LOCK(GPP_B5, NONE, LOCK_CONFIG),
        /* B6  : ISH_I2C0_SCL ==> NC */
        PAD_NC_LOCK(GPP_B6, NONE, LOCK_CONFIG),
        /* B15  : TIME_SYNC0 ==> NC */
        PAD_NC_LOCK(GPP_B15, NONE, LOCK_CONFIG),
 
        /* C3 : SML0CLK ==> NC */
        PAD_NC(GPP_C3, NONE),
        /* C4 : SML0DATA ==> NC */
        PAD_NC(GPP_C4, NONE),
 
        /* D3  : ISH_GP3 ==> NC */
        PAD_NC_LOCK(GPP_D3, NONE, LOCK_CONFIG),
        /* D5  : SRCCLKREQ0# ==> NC */
        PAD_NC(GPP_D5, NONE),
        /* D7  : SRCCLKREQ2# ==> NC */
        PAD_NC(GPP_D7, NONE),
        /* D13 : ISH_UART0_RXD ==> NC */
        PAD_NC_LOCK(GPP_D13, NONE, LOCK_CONFIG),
        /* D14 : ISH_UART0_TXD ==> NC */
        PAD_NC_LOCK(GPP_D14, NONE, LOCK_CONFIG),
        /* D15 : ISH_UART0_RTS# ==> EN_WCAM_SENR_PWR */
        PAD_CFG_GPO_LOCK(GPP_D15, 1, LOCK_CONFIG),
        /* D16 : ISH_UART0_CTS# ==> NC */
        PAD_NC_LOCK(GPP_D16, NONE, LOCK_CONFIG),
        /* D17 : UART1_RXD ==> NC */
        PAD_NC_LOCK(GPP_D17, NONE, LOCK_CONFIG),
 
        /* E0  : SATAXPCIE0 ==> WWAN_PERST_L */
        PAD_CFG_GPO(GPP_E0, 1, PLTRST),
        /* E3  : PROC_GP0 ==> NC */
        PAD_NC(GPP_E3, NONE),
        /* E7  : PROC_GP1 ==> NC */
        PAD_NC(GPP_E7, NONE),
        /* E16 : RSVD_TP ==> WWAN_RST_L */
        PAD_CFG_GPO(GPP_E16, 1, DEEP),
        /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_eMMC */
        PAD_CFG_GPO(GPP_E20, 1, DEEP),
        /* E22 : DDPA_CTRLCLK ==> SC_PWR_SV */
        PAD_CFG_GPO(GPP_E22, 1, DEEP),
        /* E23 : DDPA_CTRLDATA ==> NC */
        PAD_NC(GPP_E23, NONE),
 
        /* F19 : SRCCLKREQ6# ==> EMMC_CLKREQ_ODL */
        PAD_CFG_NF(GPP_F19, NONE, DEEP, NF1),
        /* F20 : EXT_PWR_GATE# ==> NC */
        PAD_NC(GPP_F20, NONE),
 
        /* H6  : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
        PAD_CFG_NF_LOCK(GPP_H6, NONE, NF1, LOCK_CONFIG),
        /* H7  : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
        PAD_CFG_NF_LOCK(GPP_H7, NONE, NF1, LOCK_CONFIG),
        /* H20 : IMGCLKOUT1 ==> NC */
        PAD_NC(GPP_H20, NONE),
        /* H21 : IMGCLKOUT2 ==> Privacy screen */
        PAD_CFG_GPO(GPP_H21, 0, DEEP),
        /* H22 : IMGCLKOUT3 ==> NC */
        PAD_NC(GPP_H22, NONE),
        /* H23 : SRCCLKREQ5# ==> NC */
        PAD_NC(GPP_H23, NONE),
 
        /* R6 : I2S_PCH_TX_SPKR_RX ==> NC */
        PAD_NC(GPP_R6, NONE),
        /* R7 : I2S_PCH_RX_SPKR_TX ==> NC */
        PAD_NC(GPP_R7, NONE),
 
        /* S4 : SNDW2_CLK ==> NC */
        PAD_NC(GPP_S4, NONE),
        /* S5 : SNDW2_DATA ==> NC */
        PAD_NC(GPP_S5, NONE),
        /* S6 : SNDW3_CLK ==> NC */
        PAD_NC(GPP_S6, NONE),
        /* S7 : SNDW3_DATA ==> NC */
        PAD_NC(GPP_S7, NONE),
        /*
         * E0 : SATAXPCIE0 ==> WWAN_PERST_L
         * Drive high here, so that PERST_L is sequenced after RST_L
         */
        PAD_CFG_GPO(GPP_E0, 1, DEEP),
};
 
/* Early pad configuration in bootblock */
static const struct pad_config early_gpio_table[] = {
        /* A12 : SATAXPCIE1 ==> EN_PPVAR_WWAN */
        PAD_CFG_GPO(GPP_A12, 1, DEEP),
        /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */
        PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT),
        /* H6  : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
        PAD_CFG_NF(GPP_H6, NONE, DEEP, NF1),
        /* H7  : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
        PAD_CFG_NF(GPP_H7, NONE, DEEP, NF1),
        /*
         * D1  : ISH_GP1 ==> FP_RST_ODL
         * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down.
         * To ensure proper power sequencing for the FPMCU device, reset signal is driven low
         * early on in bootblock, followed by enabling of power. Reset signal is deasserted
         * later on in ramstage. Since reset signal is asserted in bootblock, it results in
         * FPMCU not working after a S3 resume. This is a known issue.
         */
        PAD_CFG_GPO(GPP_D1, 0, DEEP),
        /* D2  : ISH_GP2 ==> EN_FP_PWR */
        PAD_CFG_GPO(GPP_D2, 1, DEEP),
        /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */
        PAD_CFG_GPO(GPP_D11, 1, DEEP),
        /* E0  : SATAXPCIE0 ==> WWAN_PERST_L */
        PAD_CFG_GPO(GPP_E0, 0, DEEP),
        /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */
        PAD_CFG_GPI(GPP_E13, NONE, DEEP),
        /* E15 : RSVD_TP ==> PCH_WP_OD */
        PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP),
        /* E16 : RSVD_TP ==> WWAN_RST_L  */
        PAD_CFG_GPO(GPP_E16, 0, DEEP),
        /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */
        PAD_CFG_GPI(GPP_F18, NONE, DEEP),
        /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (updated in romstage) */
        PAD_CFG_GPO(GPP_F21, 0, DEEP),
        /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */
        PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2),
        /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */
        PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2),
        /*
         * enable EN_PP3300_SSD in bootblock, then PERST# is asserted, and
         * then deassert PERST# in romstage
         */
        /* H13 : I2C7_SCL ==> EN_PP3300_SD */
        PAD_CFG_GPO(GPP_H13, 1, DEEP),
        /* B4  : PROC_GP3 ==> SSD_PERST_L */
        PAD_CFG_GPO(GPP_B4, 0, DEEP),
        /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_MMC */
        PAD_CFG_GPO(GPP_E20, 1, DEEP),
};
 
static const struct pad_config romstage_gpio_table[] = {
        /* B4  : PROC_GP3 ==> SSD_PERST_L */
        PAD_CFG_GPO(GPP_B4, 1, DEEP),
        /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (set here for correct power sequencing) */
        PAD_CFG_GPO(GPP_F21, 1, DEEP),
};
 
const struct pad_config *variant_gpio_override_table(size_t *num)
{
        *num = ARRAY_SIZE(override_gpio_table);
        return override_gpio_table;
}
 
const struct pad_config *variant_early_gpio_table(size_t *num)
{
        *num = ARRAY_SIZE(early_gpio_table);
        return early_gpio_table;
}
 
const struct pad_config *variant_romstage_gpio_table(size_t *num)
{
        *num = ARRAY_SIZE(romstage_gpio_table);
        return romstage_gpio_table;
}