pch.c

Go to the documentation of this file.

/* SPDX-License-Identifier: GPL-2.0-only */
 
#include <commonlib/console/post_codes.h>
#include <console/console.h>
#include <device/device.h>
#include <device/mmio.h>
#include <device/pci_ops.h>
#include <intelblocks/fast_spi.h>
#include <intelblocks/gspi.h>
#include <intelblocks/lpc_lib.h>
#include <intelblocks/p2sb.h>
#include <intelblocks/pcr.h>
#include <intelblocks/pmclib.h>
#include <intelblocks/rtc.h>
#include <soc/bootblock.h>
#include <soc/espi.h>
#include <soc/iomap.h>
#include <soc/p2sb.h>
#include <soc/pch.h>
#include <soc/pci_devs.h>
#include <soc/pcr_ids.h>
#include <soc/pm.h>
 
#define PCR_PSF3_TO_SHDW_PMC_REG_BASE   0x0C00
 
#define PCR_PSFX_TO_SHDW_BAR0   0
#define PCR_PSFX_TO_SHDW_BAR1   0x4
#define PCR_PSFX_TO_SHDW_BAR2   0x8
#define PCR_PSFX_TO_SHDW_BAR3   0xC
#define PCR_PSFX_TO_SHDW_BAR4   0x10
#define PCR_PSFX_TO_SHDW_PCIEN_IOEN     0x01
#define PCR_PSFX_T0_SHDW_PCIEN  0x1C
 
static void soc_config_pwrmbase(void)
{
        /*
         * Assign Resources to PWRMBASE
         * Clear BIT 1-2 Command Register
         */
        pci_and_config16(PCH_DEV_PMC, PCI_COMMAND, ~(PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER));
 
        /* Program PWRM Base */
        pci_write_config32(PCH_DEV_PMC, PWRMBASE, PCH_PWRM_BASE_ADDRESS);
 
        /* Enable Bus Master and MMIO Space */
        pci_or_config16(PCH_DEV_PMC, PCI_COMMAND, (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER));
 
        /* Enable PWRM in PMC */
        setbits32((void *) PCH_PWRM_BASE_ADDRESS + ACTL, PWRM_EN);
}
 
void bootblock_pch_early_init(void)
{
        /*
         * Perform P2SB configuration before any another controller initialization as the
         * controller might want to perform PCR settings.
         */
        p2sb_enable_bar();
        p2sb_configure_hpet();
 
        fast_spi_early_init(SPI_BASE_ADDRESS);
        gspi_early_bar_init();
 
        /*
         * Enabling PWRM Base for accessing
         * Global Reset Cause Register.
         */
        soc_config_pwrmbase();
}
 
static void soc_config_acpibase(void)
{
        uint32_t pmc_reg_value;
        const uint32_t pmc_base_reg = PCR_PSF3_TO_SHDW_PMC_REG_BASE;
 
        pmc_reg_value = pcr_read32(PID_PSF3, pmc_base_reg + PCR_PSFX_TO_SHDW_BAR4);
 
        if (pmc_reg_value != 0xffffffff) {
                /* Disable IO Space before changing the address */
                pcr_rmw32(PID_PSF3, pmc_base_reg + PCR_PSFX_T0_SHDW_PCIEN,
                                ~PCR_PSFX_TO_SHDW_PCIEN_IOEN, 0);
                /* Program ABASE in PSF3 PMC space BAR4*/
                pcr_write32(PID_PSF3, pmc_base_reg + PCR_PSFX_TO_SHDW_BAR4,
                                ACPI_BASE_ADDRESS);
                /* Enable IO Space */
                pcr_rmw32(PID_PSF3, pmc_base_reg + PCR_PSFX_T0_SHDW_PCIEN,
                                0xffffffff, PCR_PSFX_TO_SHDW_PCIEN_IOEN);
        }
}
 
void pch_early_iorange_init(void)
{
        uint16_t io_enables = LPC_IOE_SUPERIO_2E_2F | LPC_IOE_KBC_60_64 |
                LPC_IOE_EC_62_66 | LPC_IOE_LGE_200;
 
        /* IO Decode Range */
        if (CONFIG(DRIVERS_UART_8250IO))
                lpc_io_setup_comm_a_b();
 
        /* IO Decode Enable */
        lpc_enable_fixed_io_ranges(io_enables);
 
        /* Program generic IO Decode Range */
        pch_enable_lpc();
}
 
void bootblock_pch_init(void)
{
        /*
         * Enabling ABASE for accessing PM1_STS, PM1_EN, PM1_CNT,
         * GPE0_STS, GPE0_EN registers.
         */
        soc_config_acpibase();
 
        /* Set up GPE configuration */
        pmc_gpe_init();
 
        enable_rtc_upper_bank();
}